Verilux Indoor Furnishings VC01HH1 User Manual

®
Natural Spectrum  
ShopLight™  
INSTRUCTION  
MANUAL  
VC01HH1  
 
Important Safety Instructions  
SAVE THESE INSTRUCTIONS  
Thank you for purchasing the Verilux® Natural Spectrum® ShopLight™.  
PLEASE READ THE FOLLOWING SAFETY INFORMATION BEFORE USING.  
To reduce the risk of fire, electrical shock, or injury to persons:  
• Do NOT dismantle.  
• Do NOT alter power cord.  
Turn off/unplug and allow to cool before replacing bulb or cleaning.  
• For indoor use only.  
This portable lamp has a polarized plug (one blade is wider than the  
other). As a safety feature, this plug will fit in a polarized outlet only  
one way. If the plug does not fit fully in the outlet, reverse the plug.  
If it still does not fit, contact a qualified electrician. Never use with an  
extension cord or adapter unless plug can be fully inserted. Do not  
attempt to defeat this safety feature.  
The Verilux® Natural Spectrum® ShopLight™ is an electrical device.  
DO NOT USE NEAR WATER  
General Precautions  
Before plugging in the Natural Spectrum® ShopLight™, check to make  
sure the voltage corresponds with the main voltage of your location (120 volts).  
Do not use the Natural Spectrum® ShopLight™ outside or in wet locations  
such as bathrooms. It is intended for indoor, dry use only.  
Not for use with light dimmers, timers, motion detectors or extension cords.  
This product may cause interference with radios, cordless telephones, or  
devices that use a wireless remote control, such as televisions. If interference  
occurs, move the product away from the device, plug the product or device  
into a different outlet, or move the lamp out of the line of sight of the remote  
control receiver. This lamp complies with part 18 of FCC.  
The light bulb may become loose during transit. To reinstall the light bulb,  
see the bulb installation instructions on page 5.  
• Do NOT use lubricating agent in assembly; please see troubleshooting  
section or call Customer Service if you are having difficulty assembling  
your lamp (1-888-544-4865).  
• Unplug from electrical outlet for extended periods of non-use or during  
lightning storms to ensure protection of the electronics.  
2
 
Parts Diagram  
Main Parts & Controls  
A. Lamp Head  
B. Clamp Assembly  
C. Clamp Screw  
D. Tightening Knob  
E. Power Cord  
F. Polarized Plug  
G. Metal Wire Guard  
H. Bulb  
I. On/Off Switch  
Close-up of Lamp Head  
H
A
I
G
F
E
Fig. 1  
Fig. 3  
D
B
C
Fig. 2  
3
 
Assembly Instructions  
READ INSTRUCTIONS CAREFULLY BEFORE SET-UP  
1. Remove lamp from box and packaging. Note: Please save original  
packaging for repacking should you need to return the product.  
2. There are three mounting options:  
Wall Mount: Using #6 screws (not included) secure the clamp to  
the wall and then insert the pin into the hole of the clamp. (Fig. 1)  
Horizontal & Vertical Surface Mount: Remove clamp and turn  
the clamp screw counterclockwise until it is open slightly wider  
than the work surface to which you are attaching it. Clamp fits  
surfaces up to 1.75" thick. Surface must be a minimum of 1.5"  
deep for clamp to hold securely. (Figs. 2 & 3)  
3. Slide the clamp onto work surface, and turn plastic clamp screw  
clockwise to tighten securely.  
4. Place lamp shaft into clamp assembly and turn tightening knob  
clockwise to secure.  
5. Adjust upper and lower goosenecks as needed to illuminate work  
surface.  
6. Plug lamp into outlet and turn on; if bulb does not illuminate  
instantly, please refer to the troubleshooting section of this manual.  
Care & Cleaning  
Your Natural Spectrum® ShopLight™ is made from high quality materials  
that will last for many years with a minimum of care.You may want to  
periodically clean the lamp, using a mild non-abrasive cleaner and soft  
cloth. When cleaning, make sure you have turned off and unplugged  
the unit, and allowed sufficient time for the unit to cool.  
DO NOT USE SOLVENTS OR CLEANERS CONTAINING  
ABRASIVES, OR AMMONIA BASED CLEANERS  
All moisture should be properly wiped away and dried prior to  
restoring power.  
4
 
Bulb Removal or Installation  
Removal  
1. Unplug lamp from power source.  
2. Remove metal wire guard by depressing  
the tab and lifting it out. (See Fig. 1)  
3. Firmly hold bulb base (B) and pull  
bulb (C) from the socket (A) in  
an outward motion. (See Fig. 2)  
Fig. 1  
Installation  
1. Unplug lamp from power source.  
2. Firmly hold base (B) and push bulb (C) into the socket (A).  
(See Fig. 2 )  
3. Be sure bulb is firmly seated in the socket (See Fig. 3 below)  
and snapped into the metal bulb clip (D).  
4. Replace wire guard.  
D
• Insert metal pegs at bottom of the  
wire guard into openings near the  
bulb socket  
• Snap tab into place as shown  
(Fig. 1)  
B
C
A
Fig. 2  
Correctly seated bulb  
Incorrectly seated bulb  
No  
gap  
Notice  
large  
gap  
Fig. 3  
5
 
Troubleshooting  
®
®
Before Requesting Service on Your Verilux Natural Spectrum  
ShopLight™, Please Read the Following:  
• Make sure all power connectors, cords, and plugs are inserted fully  
and securely.  
• Be sure the bulb is securely seated into the socket. (See page 5)  
• Make sure there is power to the wall outlet or try another outlet.  
6
 
Three-Year Limited Warranty  
ATTENTION – ONCE OPENED, PLEASE DO NOT RETURN THIS  
PRODUCT TO THE STORE WHERE IT WAS PURCHASED FOR  
REPAIR OR REPLACEMENT!  
may call our customer service department at 1-888-544-4865  
This limited warranty is provided by:  
Verilux, Inc., 340 Mad River Park, Waitsfield, VT 05673  
Verilux® warrants this product to be free from defects in material and workmanship for a  
period of three years from the date of the original retail purchase. During the limited  
warranty period, Verilux, Inc. will, at its option, repair or replace defective parts of this  
product, at no charge to the customer, subject to the following limitations. This limited  
warranty does not include any postage, freight, insurance or delivery fees. This warranty  
does not cover damage, defect or failure caused by or resulting from accident, external  
destruction, alteration, modification, abuse, misuse, or misapplication of this product.  
If, during the first Three years of ownership, this product fails to operate properly, it  
should be returned as specified below.  
Please pack the defective product in its original protective packing and box, with a copy  
of your sales receipt, along with $6.95 (check or money order to cover shipping and  
handling), and send to:  
For U.S. Postal Service Only:  
Verilux Warranty Service Center  
c/o WTB  
For Fed Ex & UPS Only:  
Verilux Warranty Service Center  
c/o WTB  
P.O. Box 119, West Redding, CT 06896  
32 Henry St., Bldg 17A, Bethel, CT 06801  
Please allow 4–6 weeks before you receive the repaired or replaced product.  
ATTENTION – When returning a product, be aware that damage during  
shipping is the responsibility of the purchaser and will void any warranty  
claim. We recommend that you insure the shipment with your post office  
or other shipping service when returning this product or any parts. Be  
sure to return product in original packaging.  
®
Note: Verilux recommends using a quality surge suppressor on all electronics  
equipment. Voltage variations and spikes can damage electronic components in any  
system. A quality suppressor can eliminate the vast majority of failures attributed to  
surges and may be purchased at electronics stores.  
Due to ongoing improvements, actual product may have slight variations from the product described in this manual.  
340 Mad River Park, Waitsfield, VT 05673  
VC01HH1-MAN-Rev3  
 

Thermador Ventilation Hood VTR1030D User Manual
TomTom GPS Receiver 4EH44 User Manual
Toro Water System 220 03 User Manual
TP Link Security Camera TL SC3130 User Manual
Traulsen Refrigerator TR35761 User Manual
Troy Bilt Lawn Mower TB WC33 XP User Manual
Uniden Telephone FP098 User Manual
Victory Refrigeration Refrigerator UR 27 SAL User Manual
Viking Ventilation Hood F1570F User Manual
Vivotek Security Camera IP8335H User Manual