Velodyne Acoustics Home Theater System VX 11 User Manual

-
VX
1
1  
U S E R ’ S  
M A N U A L  
Audio/Video Subwoofer  
 
Table of Contents  
Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Crossovers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Interconnect Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Care of Your Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Protection Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Troubleshooting and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Velodyne Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
ii  
 
Congr atulations  
Congratulations on your purchase of a Velodyne subwoofer system. This system represents the  
state of the art in home audio reproduction and will provide you with years of listening pleasure  
when properly cared for. Read and follow this instruction manual to insure safe and proper  
system connection and operation.  
Caution!  
Please observe the following instructions to insure safe and proper system operation.  
Note: Do not leave unit in direct sunlight or use in high humidity environments!!!  
Warning!  
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid  
electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all  
warnings on the equipment itself. There are no user serviceable parts inside. Please refer all  
service questions to your authorized Velodyne dealer.  
Prior to Installation:  
Please unpack the system carefully. This unit is heavy. Use caution when lifting or moving to  
avoid injury. Please save the carton and all packaging materials for future use. Packing this unit  
in any other carton may result in severe damage when shipping. Record the serial number in  
the space provided on page 12 for future reference.  
Product Features  
• 10” (7.65” piston diameter) subwoofer with 1.6” high-temp voice coil  
and 32 ounce motor structure  
• High efficiency Class D amplifier  
• Adjustable (50 to 200 Hz) low-pass crossover @ 12 dB/octave  
• Line-level (RCA) inputs  
• Speaker-level inputs and outputs with spring loaded terminals  
• Signal sensing auto turn on/off  
• Variable volume control  
• Selectable phase control (0° or 180°)  
• Green power on/ Red power standby mode indicator LED  
Prepare for Installation  
Your new Velodyne subwoofer provides for a number of installation options. Read all the  
installation information below in order to determine which installation option is best for your  
system. Remember to perform all installation procedures with system power turned off  
to prevent possible damage.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
1
 
Placement  
Subwoofers operate at extremely low frequencies that are primarily omni-directional. Keep in  
mind that frequency response and output level can be drastically influenced by placement,  
depending on the acoustic properties of the listening room. Typically, the optimum location for  
a subwoofer is tucked away in a corner of your listening room where the greatest output levels  
and optimum low frequency extension can be found. The worst location for a subwoofer is far  
away from any walls and close to the center of your room. Avoid these locations when possible.  
Depending on the room size and type of furnishings in the room, perfect placement may not be  
possible. Finding the best location for your environment will likely require some experimentation.  
We suggest you experiment with the location during setup to find what sounds best to you when  
seated in your typical listening position.  
Caution! This subwoofer has electronics built into the cabinet. Do not place the cabinet  
next to sources of heat such as furnace registers, radiators, etc., or near sources of  
excessive moisture such as evaporative coolers, humidifiers, etc. The power cord should  
be routed in such a way that it will not be walked on, pinched, or compressed in any  
way that could result in damaging the insulation or wire.  
Regardless of where you install your VX-11 subwoofer, it must remain in an upright position  
(woofer facing forward). Using, shipping, or otherwise storing the subwoofer in any other  
position for an extended period of time may result in damage to the unit not covered  
by warranty.  
Installation  
Inputs  
Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL  
jacks when connecting your subwoofer to a pre-amp, signal processor, integrated receiver,  
line-level crossover, or receiver with pre-amp level outputs. These devices will often have a Low  
Frequency Effects (LFE) jack which is dedicated for subwoofer use. When using the line level  
jacks, some receivers may not provide enough signal to have the unit’s auto-on feature operate  
properly. Additionally, this lack of signal may also cause the subwoofer to produce less output  
than it is capable of.  
To alleviate this condition, we recommend the following steps:  
1)  
If using line level jacks, BOTH THE LEFT AND RIGHT INPUT SHOULD ALWAYS BE USED  
– never use just the left or just the right input. If the subwoofer’s input comes from the  
LFE channel of your receiver, use a “Y” splitter to divide the single input into two inputs  
for the Left and Right subwoofer inputs. This dual male-to-female “Y” splitter can be found  
at your local electronics store. If using line level connections from a preamp or signal  
processor, use both Left and Right inputs from your preprocessor or preamp and  
connect them to the Left and Right inputs on your subwoofer.  
2)  
If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to  
the subwoofer. We recommend setting the subwoofer’s level to the 9 o’clock position  
(the 1/4 volume setting) and then adjust the LFE channel on your receiver or processor  
to achieve the desired bass output. See your receiver or processor’s owner’s manual for  
more information.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
2
 
Note: A pair of Velodyne subwoofers is a very common setup and doubles your system’s bass  
capability. When using a pair of Velodyne subwoofers in stereo, it is preferable to place each  
subwoofer by the speaker of the corresponding channel. In this case you may have to use more  
than one “Y” splitter.  
The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated  
amplifier, or receiver. Your amplifier section will notice no additional loading effects when you  
use these inputs due to their very high impedance. If using the SPEAKER LEVEL inputs, you  
DO want to connect both channels, since different bass information might be present in each  
channel going to your main speakers.  
IMPORTANT!  
Do not use both LINE LEVEL and SPEAKER LEVEL connections simultaneously!  
Caution! To avoid damage to your main amplifier, be sure to maintain correct polarity  
when making all connections - red (positive) to red, and black (negative) to black. Be  
sure all connections are tight, and that there are no loose strands or frayed wires.  
Volume Control  
This control allows you to balance the output from the subwoofer to the main  
speakers/amplifier in your system. This control should be set to achieve similar output levels  
from both the main speakers and subwoofer when listening to music. A good starting point for  
the volume control is at the 9:00 position.  
Low-pass Crossover - 50 to 200 Hz  
A loudspeaker driver is incapable of handling all sound reproduction across the entire audio  
spectrum by itself. Thus, the crossover splits the frequency spectrum into different pieces,  
which are then handed over to individual speaker drivers. Each driver receives only the signal in  
its usable frequency range and the distortion in each driver is reduced.  
All line level inputs on the subwoofer sum the left and right channels together, with the resulting  
signal passing through an adjustable low-pass crossover before being amplified. The crossover  
control allows you to adjust the upper limit of the subwoofer’s frequency response from 50 to  
200 Hz. The subwoofer’s response will begin rolling off above the frequency you set this control  
to. You should set the crossover frequency to obtain a smooth and seamless transition from  
the subwoofer to the main speakers in your system. If your main speakers are smaller units  
with limited low frequency output, you may wish to choose a higher frequency (such as 100 -  
120 Hz) than you would with larger speakers which have greater low frequency output. With  
larger speakers, you might start with this control set lower, such as 80 Hz.  
Phase Adjustment - 0°/180°  
This control allows you to “reverse” the phase of the subwoofer’s output signal 180° to correct  
for any possible mismatch and resulting cancellation between the subwoofer and your main  
speakers/amplifier. To adjust, simply listen to the system with music playing, then ask a friend  
to adjust the phase switch from one position to the other and listen for a change in mid-bass  
output. The correct position will have a greater amount of apparent mid-bass output.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
3
 
For all installations, experiment with the phase switch to determine the setting (0 or 180  
degrees) that produces the most mid-bass. If the settings sound similar, we recommend the  
“0” position.  
Auto Turn on Function  
The subwoofer will turn itself on automatically when an audio signal is present. If no signal is  
present for approximately eight minutes, the unit will switch to standby mode (Red LED). While  
in standby mode, your subwoofer will draw very minimal power.  
4
5
6
1
2
3
7
Figure 1. Rear panel inputs, output and control layout.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
4
 
1
2
SPEAKER LEVEL OUTPUT terminals  
The speaker-level signal to the front speakers is distributed from  
these terminals.  
SPEAKER LEVEL INPUT terminals  
Connect these input terminals to the speaker output terminals  
of your amplifier or receiver.  
3
4
5
LINE INPUT jacks  
Connect these jacks to the LINE OUT jacks of the amplifier.  
VOLUME LEVEL knob  
Use this knob to adjust the output level of the subwoofer.  
Power indicator  
Red: Unit is in standby mode.  
Green: Unit is in operation mode.  
(automatically turns to STANDBY mode if no signal for eight min.)  
6
7
LOW-PASS CROSSOVER  
Use this knob to select the high-frequency range at which you wish  
to cut-off the signal to the subwoofer.  
PHASE SWITCH  
Use this switch to invert the phase of the subwoofer to create a better  
blend with your satellite speakers.  
Crossov ers  
Receiver/Processor Subwoofer Outputs  
The Velodyne subwoofer is designed to operate using the full range audio signal for input when  
using the built-in crossover. Many home theater processors/receivers (Dolby Digital™, DTS™,  
THX™) have a “subwoofer out” jack (sometimes labeled “LFE”) that is internally filtered, settable  
at the receiver/processor, and designed to be used with a powered subwoofer. In some  
installations, it may be beneficial to use BOTH the Velodyne crossover and the  
receiver/processor crossover, resulting in a steeper ultimate crossover slope. In some rare  
cases, combining both an external crossover and the one internal to the subwoofer may result  
in low output and increased noise. In these installations you may need to bypass the crossover  
in either the processor or your VX-11 subwoofer. Or, simply set one crossover to a higher  
frequency (such as 120 Hz) will restore maximum performance.  
(Refer to Figure 2a Line-Level Subwoofer Connection Diagram and Figure 2b Speaker-Level  
Subwoofer Connection Diagram, pages 7 and 8 for connection diagrams.)  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
5
 
Interconnect Cables  
When installing your new Velodyne subwoofer using the line level connections, you should always  
use shielded phono cables. There are many high quality cables available today, most any of  
which will work perfectly well. We do recommend that you keep the length of cable as short as  
possible to avoid any potential noise problems.  
When using speaker level connections, use a high quality quality speaker cable that mates well  
with the connectors. Be very careful to avoid any loose strands or frayed wires which may result  
in a short, which may damage your equipment. Cables of extremely large size are typically not  
required. Extremely large gauge wire may not properly fit in the binding posts, resulting in a  
poor connection and possible short circuits.  
Care of Your Subwoofer  
Your Velodyne subwoofer does not require any regular maintenance. Normal dusting or cleaning  
of the surface for appearance purposes is all that is required. We suggest you avoid any harsh  
detergents or chemicals when cleaning the cabinet. We recommend using only a damp cloth  
for cleaning and to avoid abrasives, detergents, or cleaning solutions which may damage the  
finish on the cabinet.  
During normal conditions, your new subwoofer may be left on continuously without any  
problems. The unit is equipped with a signal-sensing on/off switch that will automatically turn  
on the unit when a signal is present at the inputs and turn off the unit after several minutes  
when there is no longer any signal at the inputs. If your subwoofer is not to be played for an  
extended period of time we recommend you unplug the unit.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
6
 
SUBWOOFER OUTPUT JACK  
OR LFE  
REAR  
AMPLIFIER  
FRONT  
Figure 2a. Line-level subwoofer connection diagram.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
7
 
SUBWOOFER OUTPUT JACK  
REAR  
AMPLIFIER  
FRONT  
FRONT LEFT SPEAKER  
FRONT RIGHT SPEAKER  
Figure 2b. Speaker-level subwoofer connection diagram.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
8
 
Protection Circuitry  
Your new subwoofer is equipped with circuitry to provide maximum performance with  
greatest reliability.  
The unit is protected against:  
1) Overheating the amplifier.  
2) Excessive drop in power line voltage.  
If either of the above should happen, you should reduce the volume setting or shut the unit off  
until normal operating conditions return. You may also want to plug the unit into a different wall  
outlet, as dropping power line voltage will be most noticeable under strenuous conditions and  
may result in the unit shutting down intermittently.  
T roubleshooting and Service  
Before seeking service for your amplifier or subwoofer, please re-check all systems. Following  
is a simple troubleshooting guide to assist you.  
1. Verify that the unit is plugged in and power outlet used is active.  
2. Is the unit receiving an input signal from your receiver or processor?  
3. Have all controls (volume, crossover, phase, etc.) been properly set?  
4. If the unit has been running at high levels, one of the protection circuits may be  
engaged. Has the amplifier overheated?  
5. Make sure speaker-level wires are firmly attached.  
If the protection circuitry is active, the unit may cycle on and off until operating parameters  
return to normal. Under more serious conditions, the unit may shut off completely. Normal  
operation should return upon cooling, but you may be required to turn the power off and then  
on again to reset the unit.  
The following conditions require service by a qualified technician:  
1. The power cord has become damaged.  
2. The unit does not appear to operate normally or exhibits a marked  
change in performance.  
3. The unit has been exposed to water.  
4. Some part of the chassis or circuitry is physically damaged.  
Thank you for purchasing a Velodyne VX-11 Subwoofer!  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
9
 
Specifications  
MODEL  
VX -11  
Woofer  
10” forward firing (7.65” piston diameter)  
Amplifier (Class D)  
Magnet Structrure  
Frequency Response  
Voice Coil  
150 watts Dynamic, 100 watts RMS Power  
2 lbs (0.9 Kg)  
33 Hz - 140 Hz (+/-3dB)  
1.6” copper wound  
Cone  
Coated fiber  
Speaker-Level Pass-Through  
Low Pass Crossover  
Phase  
Full range  
50 Hz - 200 Hz  
0° or 180°  
Auto On/Off  
Yes  
Removable Grille  
Video Shielding  
LED Power Indicator  
Cabinet Design  
Yes  
No  
Yes  
Bass-reflex with built-in power amplifier  
15” x 12” x 17” (38 cm x 30 cm x 43 cm)  
Cabinet (H/W/D)  
(includes grille & controls)  
Shipping Weight (approx.)  
Warranty  
35 lbs. (16 Kg)  
Three years electronics (parts and labor)  
Five years driver (parts and labor)  
Specifications are subject to change without notice.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
10  
 
Velodyne Products  
115-120V  
220- 240V  
DD® Series  
DD-10  
MiniVee®  
DD® Series  
SPLi Series  
SPL-800i  
MiniVee® 10  
DD-10  
DD-12  
DD-15  
DD-12  
SPL-1000i  
DD-15  
Optimum Series  
Optimum-8  
DD-18  
Digital Drive 1812  
Signature Edition  
DD-18  
Digital Drive 1812  
Signature Edition  
SPL-Ultra Series  
SPL-800 Ultra  
Optimum-10  
Optimum-12  
SPL-1000 Ultra  
SPL-1200 Ultra  
DEQ-R Series  
DEQ-8R  
CHT-Q Series  
CHT-8Q  
SMS™-1  
SubContractor™  
Series  
DEQ-10R  
DEQ-12R  
DEQ-15R  
CHT-10Q  
CHT-12Q  
CHT-15Q  
SubContractor™  
Series  
SC-1250  
SC-10  
SC-1250  
SC-10  
SC-12  
DLS™-R Series  
DLS-3500R  
DLS-3750R  
DLS-4000R  
DLS-5000R  
SC-12  
Impact Series  
Impact-Mini  
Impact-10  
SC-15  
SC-15  
SC-IW  
SC-IW  
SC-IF/IC  
SC-IF/IC  
Impact-12  
SC-600 Amp  
SC-602 Amp  
SC-600 IW  
SC-600 IF/IC  
SC-600 Amp  
SC-602 Amp  
SC-600 IW  
SC-600 IF/IC  
MicroVee™  
SMS-1  
Impact Series  
Impact-Mini  
Impact-10  
Impact-12  
VX-11  
MicroVee™  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
11  
 
FOR YOUR RECORDS. . .  
Date Purchased_________________________________________________________________  
Dealer_________________________________________________________________________  
Serial #________________________________________________________________________  
*NOTE: Please complete and return your warranty card within ten (10) days or  
Register. . . ON LINE . . . It’s faster . . . and easier  
LIMITED WARRANTY - U.S. AND CANADA ONLY  
VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warrants all electronics for a period of three years, drivers for a period  
of five years, and full range speakers for a period of five years. All VELODYNE products have a warranty from the  
date of purchase against defects in materials and workmanship subject to the following conditions:  
1. VELODYNE is not responsible for defects which result from the use of an amplifier or controller other than  
the one originally supplied with the unit (subwoofer) or defects which result from modifications or repairs  
made by any component of the system by anyone other than a VELODYNE factory authorized  
service representative.  
2. This warranty is void if any repairs or service covered by the terms of this warranty are made to any  
component of the system by anyone other than a VELODYNE factory authorized service representative.  
3. VELODYNE is not responsible for damage caused by accidents, abuse, misuse, natural or personal disaster  
or unauthorized modification. The VELODYNE products are not intended for professional or commercial use  
and VELODYNE is not responsible for damage resulting from such use.  
4. The VELODYNE product warranty is limited to units that are purchased from authorized VELODYNE dealers  
and finalized within authorized dealer locations.  
5. This warranty is nontransferable under any condition.  
6. Use of this product outside the U.S. and Canada voids this warranty.  
TO OBTAIN SERVICE  
Information regarding service may be obtained from the dealer from whom you purchased the unit, or by contacting  
VELODYNE customer service. Warranty service must be performed by a VELODYNE factory authorized service  
representative within the warranty period set forth above. If VELODYNE determines the unit is defective, VELODYNE  
will, at VELODYNE’s option, repair or replace the product at no charge if the product is forwarded prepaid to a factory  
authorized service representative. Products forwarded to the factory authorized service representative should be  
shipped securely and properly packaged, insured and freight prepaid.  
WARRANTY OUTSIDE THE UNITED STATES AND CANADA  
The Warranty of this product if it is sold to a consumer outside of the United States or Canada shall comply with  
applicable law and shall be the sole responsibility of the distributor that supplied this product. To obtain any applicable  
warranty service, please contact the dealer from which you purchased this product, or the distributor that supplied  
this product.  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
12  
 
Velodyne Acoustics, Inc.  
345 Digital Drive  
Morgan Hill, CA 95037  
408.465.2800 voice  
408.779.9227 fax  
408.779.9208 service fax  
Service E-mail: [email protected]  
Product E-mail: [email protected]  
Technical E-mail: [email protected]  
63-VX11 Rev A AUG09  
.
w w w . v e l o d y n e . c o m  
VX-11 User’s Manual  
13  
 

Techno Source Handheld Game System 1500 User Manual
Toshiba Cell Phone STRATA DK16 User Manual
Toshiba CRT Television 30HF83 User Manual
Toshiba Personal Computer L670 User Manual
Tricity Bendix Refrigerator CSIE 510 User Manual
Tripp Lite Server 93 2879 User Manual
Troy Bilt Trimmer TB15CS User Manual
Valcom Pager V 1101A User Manual
ViewSonic Car Video System VS15465 User Manual
Vox Stereo Amplifier NT15C1 G2 User Manual