1
Introduction
This remote control is designed to operate most Digital
and Analog Cable Boxes, as well as TVs, and a VCR or
DVD player.
2
Replacing Batteries
Before you program or operate the remote control, you must
install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the
back of your remote control.
STEP2 Check battery polarity carefully, and install the batter-
ies as shown in the illustration below.
STEP3 Replace the battery compartment cover.
1
3
Button Functions
4
Programming the Remote Control.
*Note : In this section, when you are instructed to press a
[DEVICE] button, that means you should press either
the CBL, TV, or DVD button, depending on which
device you are programming the remote to operate.
A. Manual Programming
The remote control can be programmed by entering a three-
digit code number that corresponds to particular brands and
models of equipment. The three-digit code numbers are listed
in the code tables sections of this instruction manual.
2
STEP1 Turn on the equipment that you want the remote con-
trol to operate Cable Box, TV and DVD.
STEP2 Press the [DEVICE] button and the [OK/SEL] button
simultaneously for three seconds. The corresponding
device LED will turn on indicating that it is ready to be
programmed. The LED will remain on for 30 seconds.
The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and
enter the three-digit code number assigned to your
brand from the code tables. If there are more than
one three-digit number listed for your brand, try one
code number at a time until your equipment turns off.
*Note : You can verify that you have selected the correct code
by pressing the [POWER] button. The equipment
should turn on or off.
STEP4 Store the three-digit code by pressing the same
[DEVICE] button once again. The device LED will blink
twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any of the
functions do not operate as they should, repeat the
instructions from Step 2 using the next three-digit code
number from the same brand list.
B. Auto Search Method
If none of the three digit code numbers assigned to your brand
of equipment works, or the code table does not list your brand,
you can use the Auto Search Method to find the correct
three-digit code number for your equipment by following
steps:
STEP1 Turn on the equipment that you want the remote con-
trol to operate (Cable Box, TV or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button
simultaneously for three seconds. The device LED
will turn on indicating that it is ready to be pro-
grammed. The LED will remain on for 30 seconds.
The next step must be entered while the LED is on.
3
STEP3 Press the [CH+] or [CH-] button one at a time or keep
it pressed. The remote will emit a series of Power
ON/OFF code signals. Release the [CH+] or [CH-] but-
ton as soon as the equipment turns off.
*Note : You can verify that you selected the correct code by pressing
the [POWER] button. The equipment should turn On or Off.
STEP4 Press the same [DEVICE] button to store the code.
The Device LED will blink twice to confirm that the
code has been stored.
C. To find the Three-Digit Code that Was
Programmed using the Auto Search Method
STEP1 Press the appropriate [DEVICE] button and the
[OK/SEL] button simultaneously for three seconds.
The device LED will turn on for 30 seconds. The next
step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink a
number of times indicating the number of each digit
for the code. Each digit is separated by a one second
interval of the LED being off.
Example : One blink, then three blinks, then eight blinks indi-
cates the code number 138.
*Note : Ten blinks indicates the number 0.
D. Programming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL] button
simultaneously for 3 seconds. The DVD LED will turn
on for 30 seconds. The next step must be performed
while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the
three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD] but-
ton. The device LED will blink twice to confirm that
the code has been stored.
4
E. The Learning Method
STEP1 Press the [COMPONENT] button (CBL, TV or DVD) to
be programmed and the [INPUT] buttons simultane-
ously for 3 seconds until the Component LED light
turns on.
STEP2 Line up the UR3L-SR4 to the other remote, head-to-
head, 1 or 2 inches apart.
STEP3 Press any button on the UR3L-SR4 that you want to
teach a command to. For example, if you want to
teach the [MUTE] button, press the [MUTE] button.
STEP4 Press and hold the [MUTE] button on the other remote
until the UR3L-SR4 Component LED light blinks twice.
*Note : The LED will blink 5 times if there was an error in the
learning process. In so, repeat STEPS 3 and 4. Continue
learning other buttons by repeating STEPS 3 and 4.
STEP5 Once you have completed teaching UR3L-SR4 all
desired commands for that Component, save the
learned commands by pressing the [COMPONENT]
and [INPUT] buttons simultaneously until the
Component LED blinks 3 times. Now test all the but-
tons to make sure they learned correctly.
F. Erasing a Single Learned Command
STEP1 Press the [COMPONENT] and [INPUT] buttons simul-
taneously for 3 seconds until the Component LED
light turns on.
STEP2 Press and hold the button you want to erase for 3
seconds. The Component LED will blink twice to con-
firm the erasure.
STEP3 To exit, press and hold both the [COMPONENT] and
[INPUT] buttons simultaneously until the Component
LED blinks 3 times.
5
G. Erasing All Learned Commands from
One Component
STEP1 Press the [COMPONENT] and [INPUT] buttons simul-
taneously for 3 seconds until the Component LED
light turns on.
STEP2 Press and hold both the [COMPONENT] button you
want to erase and the [PAUSE] button for 5 seconds.
The Component LED will blink twice to confirm the
erasure.
STEP3 To exit, press and hold both the [COMPONENT] and
[INPUT] buttons simultaneously until the Component
LED blinks 3 times.
H. Programming the All Off Button
This allows you to program the All Off button so it can send up
to three power On/Off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [All OFF] button and the [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button will
turn on for 30 seconds.
STEP3 Press the first [COMPONENT] button you want to
store in the [ALL OFF] button and then the [POWER]
button. Repeat this for other Components until you
have stored all the desired power commands into the
[ALL OFF] button.
STEP4 Press the [CH+] button to save the power commands
you stored. The [CBL] button will blink twice to con-
firm the commands have been saved.
I. Programming for Advanced Functions.
If your remote model has custom-programmable Macro but-
tons available, they can be programmed to act as a ‘Macro’ or
Favorite Channel button in CABLE mode. This allows you to pro-
gram up to five 2-digit channels, four 3-digit channels or three 4-
digit channels that can be accessed With one button press.
6
**Note : The FAV button is not programmable if you have a
Digital Cable Box made by Pace, Pioneer or
CISCO/SA.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button will
turn on for 30 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you
want programmed first (for example, 007) using the
Number Pad, then press the [STOP] button. Then
enter the code for the next channel (for example,
050), then press the [STOP] button. Repeat this
process for the third channel. The [CBL] button will
blink once for each channel entered.
STEP4 Press the [CH+] button to store the channels that
were selected. The [CBL] button will blink twice to
confirm the storage of commands.
To access the programmed channels, press the [MACRO]
button once. This will bring up the first channel. Press once
again and it will bring up the second channel. Press again
and it will bring up the third channel.
To erase the Macro programming and return to the original
function:
STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the [OK/SEL] button
simultaneously for 3 seconds. The CBL device LED
will turn on for 30 seconds. The next step must be
performed while the LED is on.
STEP3 Press the [CH+] button to erase the functions stored
in the button. The CBL device LED will blink twice to
confirm that the memory button has been erased.
7
J. Assigning the Volume and Mute keys to a
Different Device
CBL : TV TV : TV DVD : TV
STEP1 Press the [OK/SEL] button and [CBL] button simulta-
neously for three seconds. The device LED Will turn
on for 30 seconds. The next step must be performed
while the LED in on.
STEP2 Press the [VOL+] button. The device LED will blink.
STEP3 Press the [CBL] button corresponding to the device
that you would like the volume and mute buttons to
control. The device LED will blink twice to confirm
the programming.
Example : If you wish to have the volume and mute keys oper-
ate your TV, press the [TV] button in Step3.
K. Assigning the Channel keys to a Different
Device
CBL : CBL TV : CBL DVD : DVD
STEP1 Press the [OK/SEL] button and [TV] button simultane-
ously for three seconds. The device LED Will turn on
for 30 seconds. The next step must be performed
while the LED in on.
STEP2 Press the [VOL-] button. The device LED will blink.
STEP3 Press the [TV] button corresponding to the device
that you would like the volume and mute buttons to
control. The device LED will blink twice to confirm
the programming.
*Note : If you wish to have the channel keys operate your Cable Box,
press the [CBL] button instead of the [TV] button in Step3.
8
L. Low Battery Warning
When the battery is low (2.3V-2.0V) and needs to be replaced
with fresh batteries, device LED will blink 2 times in sequence
whenever a [DEVICE] button is pressed to turn on equipment.
M. Memory Lock System.
This remote control is designed to retain programmed memo-
ry for 10 years — even after batteries are removed from the
remote control.
For additional information about your remote control, go to
9
5
Set-up Code Tables
CABLE TV
MAKER(BRAND) NAME
CISCO/SA
CONVERTER
EXPLORER Series
8600X
CODE No
001 007
011
8600
8540,8570,8590
8500
021
022
023
MOTOROLA
DCT Series (DVR Model)
002
008
GENERAL INSTRUMENT DCT Series,DCH Series, CFT2200
JERROLD
DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027
DIGEO
DIRECTV
MOXI
2056-MSX
153
229
006
052
153
HR20,HR21
MOXI MEDIA CENTER
MOXI HD DVR
2056-MSX
NFUSION
NSC
NUVENIO SD PHOENIX, NUVENIO HD,
SOLARIS, NOVA
IM781R
192
046
047
IM781
PACE
500 Series
TDC Series
001 007
002
510
004
001 007
013
001 007
130
230
PIONEER
SAMSUNG
SKY
VOYAGER Series
BA9000
OCAP MODELS
SKY+HD
SKY HD
204
TELNET
RC-RW100
154
10
TV
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
072 081 160 161 096
147
ADMIRAL
ADVENT
AIWA
141 145
AKAI
070 146 004 148 124 226 104 108
AKIO
103
ALARON
AMARK
028
112 127
AMERICA ACTION 043
AMPRO
073 167
ANAM
043 054 056 080 112 131
AOC
058 070 004 112
APEX
092
APEX DIGITAL
AQUAVISION
AUDIOVOX
AVION
015 150 037
097 100
076 103 043 035 078 224
223
BAYSONIC
BELL&HOWELL
BRADFORD
BROKSONIC
CAIRN
043
072
043
096 170
162
CANDLE
070 002 003 004
CAPEHART
CARVER
058
164
CELEBRITY
CETRONIC
CINERAL
CITIZEN
001
043
103 120
070 002 003 004 101 103 127
CLASSIC
CONCERTO
CONTEC
CORONADO
CRAIG
043
004
043 051
127
043 054 028
164
CROSLEY
CROWN
043 127
CURTIS MATHES 070 004 101 011 072 081 120 164 127
CXC
043
DAEWOO
DAYTRON
DELL
076 103 112 004 127 016 043 044 125 120
004 127
041
DENON
011
DIGITAL PROJECTION 090
DUMONT
DWIN
DYNASTY
DYNATECH
004 073
131 132 161
043
062
11
TV
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
FISHER
007 057
001
024 076 127
ELECTROBAND
ELECTROHOME
ELEMENT
004 110
EMERSON
005 028 043 048 076 096 155 004 051 151 153 154
127 121
ENVISION
EPSON
070
087 228
ESA
031
FUJITSU
FUNAI
164 197 028 157 149 066 217
028 043 052 168
FUTURETECH
GATEWAY
GE
043
165 031
070 073 130 144 160 161 004 008 009 034 056 074
091 155 081 120
031
GEM
GIBRALTER
GOLDSTAR
GRUNPY
HAIER
HALL MARK
HANNSPREE
004 073
004 106 112 127
028 043
004 116
004
099
HARLEY DAVIDSON 028
HARMAN KARDON 164
HARVARD
HISENSE
HITACHI
HP
043
198 021
004 007 009 011 072 010 012 023 075 158 127 174
027 039 098
HUMAX
HYUNDAI
ILO
122
049 067
055 096
INFINITY
INFOCUS
INKEL
164
046 215 225
129
INSIGNIA
INTEQ
068 069 078 096 164 168
073
JBL
164
JCB
001
JCPENNEY
JENSEN
JVC
004 008 024 030 065 070 101 160 156 127
013
038 001 034 083 195 159 227
KENWOOD
KLEGG
KLOSS
KREISEN
KTV
070 001
220
002 059
202
070 043 154 127
12
TV
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
004 106 112 127 086
LG
LODGENET
LOEWE
LOGIK
072
196 164
072
LUXMAN
LXI
004
007 015 052 081 160 164
MAGNAVOX
070 003 004 022 059 060 061 063 064 127 164 094
160 056 028 035 211 205 218 050 138
MAJESTIC
MARANTZ
MATSUI
MATSUSHITA
MAXENT
MEGATRON
MEMOREX
METZ
072
164 070 143 169
164
080
165
004
004 007 072 028 096
088
MGA
024 070 004 042
MIDLAND
MINERVA
MINTEK
MINUTZ
MITSUBISHI
MOTOROLA
MTC
073
088
077
008
109 024 042 004 040 146 028 124 081 200
081
070 004 062 101
MULTITECH
NAD
043
015 025
NEC
070 130 134 040 056 007 019 024 004 182 140
NIKEI
043
NIKKO
103
NIKO
175
NORCENT
NTC
211
103
NUVISION
OLEVIA
084
219 004 161 144 160
ONKING
ONWA
043
043
OPTIMUS
OPTOMA
OPTONICA
ORION
080
029 032
019 081
096 201 203 204 205 028
PANASONIC
PHILCO
PHILIPS
034 056 080 164 190 230 248
070 003 004 024 056 059 060 063 064 127 164
164 005 038 093 127 070 003 004 059 199 218 161
232
PIONEER
POLAROID
023 025 135 176 004 018 070 183 191 208 214 182
026 118 119 006
13
TV
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
004 103 127
034
PORTLAND
PRISM
PROSCAN
PROTON
PROTRON
PROVIEW
PROX
144 160 161 167
004 058 171 173 193 127 163
102 213 004 115
110
092
QUASAR
RADIO SHACK
RCA
034 056
004 019 127 043
160 161 144 156 065 070 004 023 024 056 074 152
081 209
007 019
REALISTIC
REVOLUTION HD 220
RUNCO
072 073 130 179 180 181 182 216 194
SAMPO
070 004 058 165
SAMSUNG
SANSEI
004 101 127 133 160 089 105 070 184 185 192
120
SANSUI
096
SANYO
007 053 057 082 020
SCEPTRE
SCOTCH
SCOTT
036
004
004 005 028 043 048 127 113
SEARS
004 007 015 028 030 057 082 094 160 052 164 127
SELECO
189
SEMIVOX
SEMP
043
015
SHARP
081 014 019 028 004 022 127
SHERWOOD
SIGNATURE
SOLE
128
072
177 178
SONY
001 085 126 139
SOUNDESIGN
SOYO
003 004 028 043
163
SPECTRICON
SPECTRONIQ
SQUAREVIEW
SSS
112
004
052
004 043
STARLITE
SUPRE MACY
SUPREME
SVA
043
002
001
046
SYLVANIA
070 003 059 060 063 064 127 160 164 044 056 168
121 231
SYMPHONIC
SYNTAX OLEVIA
TANDY
052 168
219 004 161 144 160
081
14
TV
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
TATUNG
056 062
034 080
028
246
004
TECHNICS
TECHNOL ACE
TECHVIEW
TECHWOOD
TEKNIKA
TELERENT
TERA
002 003 004 024 028 043 072 101 103 164 127
072
172
THOMPSON
TNCI
166
073
TMK
004
TOSHIBA
TOTEVISION
TRUTECH
UNIVERSAL
015 030 007 040 062 101 142 045 137
127
212
008 009
VIDEO CONCEPTS 146
VIDIKRON
VIDTECH
VIEWSONIC
VIORE
188 164 182
004
210 211
055 229
VISCO
110
VIZIO
004 031
WARDS
004 064 164 008 009 019 028 060 061 063 072 074
070 127
WESTINGHOUSE 076 036 221 222 001
WINBOOK
YAMAHA
YORK
079
004 070 206 207
004
YUPITERU
ZENITH
ZONDA
043
011 072 073 095 103 096
112
15
DVD
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
ADCOM
AIWA
AKAI
203
210 214
239
ALPINE
APEX DIGITAL
ARCAM
AUDIOVOX
BOSE
179
240 197 247 248 196
165 148
075
244 245
CAMBRIDGE AUDIO 224 145
CARY AUDIO DESIGN 249 149
CLASSE
COBY
242
206
CYBERHOME
DAEWOO
DENON
170 212
170
184 226 225
DURABRAND
EMERSON
ESA
235
235
235
FUNAI
235
GE
188 189
GOLDSTAR
GO VIDEO
GRADIENTE
182 194
228 182 252 253 254
243
HARMAN KARDON 217
HITACHI
HITEKER
INSIGNIA
INTEGRA
JVC
181
197
078 235 085 182 178
208 236 238 128
185
KENWOOD
KISS
166
237
KLH
230
KOSS
243
KRELL
218
LEXICON
LG
216
182 194
150
178 191 195 235
176 177 135
167
222
200
240 196
186
211
LITEON
MAGNAVOX
MARANTZ
MCINTOSH
MEMOREX
MERIDIAN
MINTEK
MITSUBISHI
MYRYAD
NAD
198 182
16
DVD
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
207 236 128
ONKYO
OPPO
125
OPTIMUS
ORITRON
PANASONIC
PARASOUND
PHILIPS
PIONEER
POLAROID
PRIMARE
PROCEED
PROSCAN
RCA
187
243
076 173 184 219 192
083
074 164 176 177 191 195 209 127
175 180 187 221 223
075 084 085
250 251
172
188 189
188 189 086
SANSUI
201
SANYO
215
SAMSUNG
183 193 228 205 073 152 241
SENSORY SCIENCE 254 255
SHARP
174
SHERWOOD
SONY
083
077 168 190 213 118 119 120 121 126
SPECTRONIQ
SUPERSCAN
SV2000
088
235
235
SYLVANIA
SYMPHONIC
TAG McLaren
TECHNICS
THETA DIGITAL
TOSHIBA
235
235
202
173
187
169 171 191 206 227 201 236
TRUTECH
VENTURER
VINC
151
229
220 087
YAMAHA
ZENITH
199 204 246 184 192
182 194
DVR(TIVO)
DIRECTV
HUGHES
HUMAX
819
817
817
PHILIPS
RCA
790 817
809
REPLAY NETWORKS 775
SONY
804 805
TIVO
TOSHIBA
790 817
817
17
VCR(DVD)
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
ADVENTURA
AIWA
AKAI
534
534
543
645
ANAM
AUDIO DYNAMICS 512 543
AUDIOVOX
BROOKSONIC
CALIX
601
629
601
CANON
645
CITIZEN
CRAIG
601
503 602
CURTIS MATHES 645
DAEWOO
DBX
DYNATECH
ELECTROHOME
612
512 543
534
559
ELECTROPHONIC 601
EMERSON
FISHER
FUNAI
506 645 534 601 629 631 653
503 508
534
GARRARD
GE
GO VIDEO
GOLDSTAR
GRADIENTE
534
645 647 644
602
601 513 512 623
534
HARLEY DAVIDSON 534
HARMAN KARDON 512
HITACHI
HQ
534 543 513
534
INSTANTREPLAY 645
JCL
645
JCPENNEY
JENSEN
JVC
512 513 602 601
543
548 543 512 645
601
KEC
KENWOOD
KODAK
LG
LLOYD
LXI
MAGIN
MAGNAVOX
MARANTZ
MARTA
MATSUSHITA
MEI
548 534
645 601
601 513 512 623
534
534 503
602
567 645 534
567 512 645
601
645
645
18
VCR(DVD)
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
601 503 645 534 602
513
559 513
645
MEMOREX
MINOLTA
MITSUBISHI
MOTOROLA
MTC
534 602
MULTITECH
NEC
534
512 543 548
NIKKO
601
NORDMENDE
OPTIMUS
PANASONIC
PENTAX
PHILCO
543
601
570 645 667
513 645
645 534 567
PHILIPS
PILOT
645 567 534 601
601
PIONEER
RADIO SHACK
RADIX
513 548
623
601
RANDEX
RCA
601
644 647 645 513 534 602
REALISTIC
RICO
503 508 645 534 602 601
558
SAMSUNG
SANSUI
602 612 644 647
543 548
SANYO
503 602
SCOTT
612 629 631
SEARS
503 508 513 601 612
SHARP
649 645
SIGNATURE
SONY
534
557 558 503 645 649 654
SOUNDESIGN
STS
534
513
SYLVANIA
SYMPHONIC
TANDY
645 534 559 567
534
534
TATUNG
TEAC
TECHNICS
TEKNIKA
THOMAS
TMK
543
534 543
645 570
645 534 601
534
506
TOSHIBA
TOTEVISION
UNITECH
612 631 508 559 513
602 601
602
VECTOR RESEARCH 512
VICTOR 548
19
VCR(DVD)
MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST
VIDEO CONCEPTS 512 534
VIDEOSONIC
VILLAIN
602
534
WARDS
503 513 645 534 602 631
645 534
512 534 543
XR-1000
YAMAHA
ZENITH
548 601 534 558
TV/VCR Combos
EMERSON
FUNAI
653
534
GOLDSTAR
601 623
HARLEY DAVIDSON 534
HITACHI
JCPENNEY
LG
534
601
601 623
534
LLOYD
MAGNAVOX
MEMOREX
PANASONIC
PHILIPS
RADIO SHACK
RCA
534 567
601
570 667
534 567 645
623
534 644
602
601
SAMSUNG
SEARS
SONY
557 654 558
567
534
534
534
SYLVANIA
SYMPHONIC
THOMAS
ZENITH
20
21
OCE-0082A
Rev 01
|