Uniden Telephone EXP 9100 User Manual

Table of Contents  
About Your EXP 9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
FCC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
EXP 9100 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Automatic Digital Code Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Auto Channel Scan and Auto Channel Change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Spread Spectrum Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Auto Power Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Installing Your EXP 9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Selecting the Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Connecting the Telephone Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Installing the Base Unit on a Desk or Tabletop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Mounting the Base Unit on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Installing the Battery Pack (BT-9100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Preparing the Base Unit and Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Special Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Using Your EXP 9100 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Using your EXP 9100 Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Using the EXP 9100 as a Room Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Telephone Line Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Base Unit Controls & Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Handset Controls & Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
1
 
12. Unplug this product from the wall outlet and refer servicing to qualified  
service personnel under the following conditions:  
A. When the power supply cord is damaged or frayed.  
B. If liquid has been spilled into the product.  
C. If the product has been exposed to rain or water.  
D. If the product does not operate normally when following the operat-  
ing instructions. Adjust only those controls that are covered by the  
operating instructions. Improper adjustment of other controls may  
result in damage, and will often require extensive work by a qualified  
technician to restore the product to normal operation.  
E. If the product has been dropped, or the cabinet has been damaged.  
F. If the product exhibits a distinct change in performance.  
13. Do not use the telephone to report a gas leak in the vicinity of the leak.  
CAUTION: TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS  
BY THE BATTERY, READ AND FOLLOW THESE INSTRUCTIONS:  
1. Use only the appropriate type and size Battery Pack specified in this  
Operating Guide.  
2. Do not dispose of the Battery Pack in a fire. The cell may explode.  
Check the Nickel-Cadmium Battery Disposal package insert for disposal  
instructions.  
3. Do not open or mutilate the Battery Pack. Released electrolyte is  
corrosive and may cause damage to the eyes or skin. It may be toxic if  
swallowed.  
4. Exercise care in handling the battery in order not to short the battery  
with conducting materials such as rings, bracelets, and keys. The  
battery or conductor may overheat and cause burns.  
5. Charge the Battery Pack provided with or identified for use with this  
product only in accordance with the instructions and limitations specified  
in the instruction manual provided for this product.  
6. Observe proper polarity orientation between the Battery Pack and  
battery charger.  
SAVE THESE INSTRUCTIONS  
3
 
About Your EXP 9100  
Congratulations on your purchase of the Uniden EXP 9100 Cordless  
Telephone. The EXP 9100 is designed and engineered to exacting standards  
for reliability, long life, and outstanding performance. To get the most from your  
EXP 9100, please read this Operating Guide thoroughly. Refer to the foldout  
located in the back of this Operating Guide to help familiarize you with the  
features of your cordless phone. Also, be sure to fill out the Product  
Registration card at the back of this Guide, then detach and mail in.  
Unpacking  
Your EXP 9100 box should contain the following items:  
Base Unit  
Handset  
Telephone Line Cord  
AC Adapter ( AD-9100)  
Wall Mount Adapter  
Rechargeable Battery Pack (BT-9100)  
This Operating Guide (read thoroughly)  
Nickel-Cadmium Battery Disposal Notice  
Memory Storage Stickers  
If any of these items are missing or damaged, do not contact the place of  
purchase. Instead, contact Uniden Customer Service at: (800) 297-1023 8 a.m.  
to 5 p.m., Central, Monday through Friday.  
FCC Requirements  
You are no longer required by the FCC to notify your local telephone company  
of your intent to connect a new telephone. Your local telephone company may  
call you and request information about your phone such as the brand name,  
model number, registration number, and ringer equivalence number. This  
information is provided on a label located on the bottom of the Base Unit.  
If your EXP 9100 Cordless Telephone is not performing up to your  
expectations, please try the simple steps listed in the Troubleshooting, Range,  
and Radio Interference sections of this manual. If you are still unable to resolve  
the problems, please contact Uniden Customer Service.  
If the unit must be returned for service, ship or deliver the product, freight prepaid to:  
Uniden America Corporation  
Parts and Service Division  
4700 Amon Carter Blvd.  
Ft. Worth TX 76155  
4
 
EXP 9100 Features  
Spread Spectrum Technology  
UltraClear Plus noise reduction provides the quality sound  
of a corded telephone.  
Auto Power Control  
Tone/Pulse Dialing  
20-Number Memory  
Maximum Operating Range  
3 One-Touch Memory Dialing Buttons  
Room Monitoring  
2-Way Paging/Intercom  
Redial/Pause and Flash  
Spare Battery Charger/Battery Back-Up  
AutoStandby  
AutoTalk  
Auto Channel Scan  
Auto Channel Change  
Automatic Digital Code Security  
Handset Volume Control/Ringer Volume Control  
Base Unit Ringer Volume Control  
Battery Saving Feature  
2-Way Handset Mounting  
Reversible Handset Retainer  
Mute  
Hold  
Lighted Keypad  
Automatic Digital Code Security  
Many cordless telephones operate similarly and on the same frequency.  
Without digital code security, another Handset could make calls using your  
Base Unit and telephone line. Therefore, to avoid any unauthorized calls  
through your Base Unit, a Digital Code feature was added to your EXP 9100.  
This Digital Code is shared only between the Handset and Base Unit. The  
Code is set automatically when you first use the phone.  
To reset the Digital Code:  
1. Be sure the Handset is on the Base Unit.  
2. Press INT’COM on the Base Unit. The Base Unit and Handset will begin  
beeping.  
3. Remove the Handset from the Base Unit and set it down again. The  
Base Unit and Handset will stop beeping.  
The Digital Code is now reset randomly to one of more than 65,000 codes.  
5
 
If the Base Unit loses power while the Handset is off the Base, the Digital Code  
may be erased. When this happens, the Handset will not function. To restore  
the Digital Code:  
1. Remove the Handset from the Base Unit (if it is on the Base Unit).  
2. Restore power to the Base Unit.  
3. Place the Handset back on the Base Unit.  
The CHARGE LED will blink twice to indicate that the Digital Security Code is set.  
NOTE: It may take up to 5 seconds to establish contact between the  
Handset and Base Unit and reset the Digital Security Code.  
Auto Channel Scan and Auto Channel Change  
During a call, your EXP 9100 constantly monitors the noise level of the channel.  
If the channel becomes too noisy, the unit automatically switches to a clearer  
channel to maintain the best transmission quality.  
Spread Spectrum Technology  
Your EXP 9100 uses Spread Spectrum Technology which provides a digital link  
between the Base Unit and Handset. This advancement results in unparalleled  
security, virtually eliminating any chance of outside monitoring, and greatly  
improves noise reduction for top-quality sound in your cordless phone.  
Auto Power Control  
The EXP 9100 automatically sets the Handset RF power level, depending on  
the distance from the Base Unit. When the Handset is near the Base Unit, the  
RF power level is low. When the Handset is at a greater distance from the  
Base Unit, the RF power level is set automatically to high. This provides the  
clearest possible communications while making the most efficient use of the  
battery power.  
6
 
Installing Your EXP 9100  
Selecting the Installation Location  
Select a location for the EXP 9100 to avoid excessive heat or humidity (as in a  
kitchen or bathroom). The Base Unit of your EXP 9100 can be placed on a  
desk or tabletop near a standard 120V AC outlet and telephone line jack, or  
mounted on a standard AT&T or GTE wall plate. Keep the Base Unit and  
Handset away from sources of electrical noise (motors, fluorescent lighting).  
Connecting the Telephone Line  
There are three types of phone outlets: 1) Modular, 2) 4-prong jack, or  
3) hard-wired type.  
1) Modular Jack  
Plug the telephone line cord from the Base Unit into a standard modular  
telephone jack. (Note: If you do not have a modular jack, contact your local  
telephone company for information on the installation of these jacks.)  
2) 4-Prong Jack  
An adapter (not included) is required. The adapter plugs into the 4-prong  
jack and the telephone line cord plugs into the adapter.  
3) Hard-wired Jack  
A modular jack converter (not included) is required. You may need to rewire  
when connecting the converter (making color-coded connections).  
(Note: Your Uniden Cordless Telephone Dealer or a telephone supply store  
can advise you on the proper adapter or converter.)  
There are two telephone line jacks in the EXP 9100: “LINE IN” and  
“LINE OUT”.  
NOTE:  
You can connect the Telephone Line Cord to either jack.  
CAUTION:  
Never install telephone wiring during a lightning storm.  
Never install telephone jacks in wet locations unless the jack is  
specifically designed for wet locations.  
Never touch uninsulated telephone wires or terminals unless the  
telephone line has been disconnected at the network interface.  
Use caution when installing or modifying telephone lines.  
7
 
Installing the Base Unit on a Desk or Tabletop  
NOTE: Refer to the foldout located in the back of this Operating Guide to  
help familiarize you with the controls of your cordless phone.  
1. Place the Base Unit on  
a desk or tabletop, and  
plug one end of the  
Telephone Line Cord  
(supplied) into the  
LINE IN” jack on the  
Base.  
2. Plug the other end of  
the Telephone Line  
Cord into the telephone  
wall jack.  
3. Plug the AC Adapter  
cord into the AC  
Adapter input jack on  
the Base Unit.  
(Note: Use only the AC Adapter supplied with the EXP 9100.)  
4. Plug the AC Adapter into a standard 120V AC wall outlet.  
5. Route the power cord where it will not create a trip hazard, or where it  
could become chafed and create a fire or other electrical hazards.  
The unique design of your EXP 9100 allows you to place the Handset on the  
Base Unit either face down or in an upright position. Also, you may extend the  
legs on the bottom of the Base Unit, placing it at an angle for better visibility of  
the LEDs (See the Base Unit Fold-out illustration). Remove the Handset  
Support in the charging cradle so the handset remains in a stable, upright  
position. The Battery Pack in the Handset automatically recharges in either  
position.  
8
 
Mounting the Base Unit on a Wall  
Installing the Wall-Mount Adapter on the Base Unit  
1. Remove the Handset from  
the Base Unit.  
2. Lay the Base Unit face  
down on a flat, smooth  
surface.  
3. Insert the two front tabs of  
the Wall Mount Adapter into  
the two receptacles next to  
the legs of the Base Unit.  
4. Squeeze the two side tabs  
of the Wall Mount Adapter  
and snap them into the  
receptacles near the bottom  
edge of the Base Unit.  
Setting the Handset Retainer  
1. Remove the Handset Retainer on the Base Unit by sliding it upward.  
2. Flip the Retainer over so the tab is facing up.  
3. Slide the Retainer back into the Base Unit.  
The Base unit of your EXP 9100 is now ready to be mounted on a standard wall  
plate or mounted directly to a wall.  
9
 
Mounting on a Standard Wall Plate  
1. Plug one end of the  
Telephone Line Cord  
(supplied) into the “LINE IN  
jack on the top of the Base  
Unit. Lay the cord inside the  
molded channel on the  
bottom of the Wall Mount  
Adapter connected to the  
Base Unit. (Put any excess  
line cord inside the Wall  
Mount Adapter.)  
2. Plug the other end of the  
Telephone Line Cord into  
the telephone wall jack.  
3. Plug the AC Adapter cord  
into the AC Adapter input  
jack on the Base Unit.  
(Note: Use only the AC  
Adapter supplied with the EXP 9100.) Place the cord inside the molded  
channel on the Wall Mount Adapter connected to the Base Unit.  
4. Place the Base Unit on the two posts of the wall plate and slide  
downward to secure. Then hang the Handset on the Base Unit.  
5. Plug the AC Adapter into a standard 120V AC wall outlet.  
6. Route the power cord where it will not create a trip hazard, or where it  
will not become chafed and create a fire or other electrical hazards.  
If you do not have a standard wall plate, you can mount the Base Unit directly  
on a wall.  
Mounting Directly on a Wall  
1. Carefully select a location away from electrical cables, pipes, or other  
items behind the mounting location that could cause a hazard when  
inserting screws into the wall.  
2. Insert the two mounting screws 3516 inches apart vertically, allowing  
about 15 of an inch between the wall and screw heads for mounting the  
phone. Make sure the screws are securely fastened, and that the wall  
material is capable of supporting the weight of the Base Unit; otherwise,  
damage to the Base Unit could result.  
3. Plug one end of the Telephone Line Cord (supplied) into the “LINE IN  
jack on the Base Unit. Lay the cord inside the molding on the Wall  
Mount Adapter connected to the Base Unit.  
Download from Www.Somanuals.co1m0. All Manuals Search And Download.  
4. Plug the AC Adapter cord into  
the AC Adapter input jack on  
the Base Unit.  
(Note: Use only the AC  
Adapter supplied with the  
EXP 9100.) Place the cord  
inside the molded channel on  
the Wall Mount Adapter  
connected to the Base Unit.  
5. Place the Base Unit onto the  
mounting screws and slide  
downward to secure. Then  
hang the Handset on the  
Base Unit.  
5. Plug the other end of the  
Telephone Line Cord into the  
telephone wall jack.  
7. Plug the AC Adapter into a  
standard 120V AC wall outlet.  
8. Route the power cord where it will not create a trip hazard, or where it  
will not become chafed and create a fire or other electrical hazards.  
Installing the Battery Pack (BT-9100)  
1. Remove the battery compartment  
cover on the Handset by sliding it  
down.  
2. Slide in the Nickel-Cadmium  
Battery Pack (Note: The Battery  
Pack is keyed to fit so the electrical  
contacts touch the Handset’s  
electrical contacts.)  
3. Slide the battery compartment  
cover back on.  
After removing the Battery Pack, the  
built-in Memory Backup feature allows  
up to 3 minutes to install a charged  
Battery Pack. This feature prevents  
losing any phone numbers that may be  
stored in the telephone’s memory.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Charging the Handset’s Battery Pack  
The rechargeable Nickel-Cadmium Battery Pack must be fully charged before  
using your EXP 9100 for the first time. (Note: Allow the unit to charge without  
interruption for 5-7 hours.)  
1. Place the Handset on the Base Unit.  
2. Make sure the CHARGE LED lights.  
If the CHARGE LED does not light, check to see that the AC Adapter is  
plugged in.  
Charging Extra Battery Packs  
The Base Unit of your EXP 9100 is equipped with a Spare Battery Charger for  
charging an extra Battery Pack.  
1. Press the door to open  
the Spare Battery  
Charger.  
2. Slide in the  
Nickel-Cadmium Battery  
Pack so it rests on top of  
the ribbon. (Note: The  
Battery Pack is keyed to  
fit so the electrical  
contacts touch the Spare  
Battery Charger’s  
electrical contacts.)  
The BATTERY CHARGE  
LED should light. If the  
BATTERY CHARGE LED  
does not light, check to  
see that the AC Adapter  
is plugged in.  
3
Press the door to close  
the compartment.  
Note: Allow the Battery Pack to charge without interruption for 5-7 hours.  
When charging is complete, use the ribbon to remove the Battery  
Pack from the Spare Battery Charger.  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
Base Unit Battery Back-Up Feature  
If AC power to the Base Unit fails, and the Spare Battery Charger contains a  
battery, the Base Unit will keep operating from the spare battery. This feature  
prevents the system from going dead during a power outage.  
Low Battery Indicator  
When the Battery Pack in the Handset is very low and needs to be charged, the  
TALK LED flashes every 3 seconds. If this occurs while you are on the phone, a  
short alert beep will also sound. When this happens:  
1. Complete your call as quickly as possible. Once the battery is low, you  
will only be able to press the TALK button, returning the phone to  
Standby.  
2. Return the Handset to the Base Unit for charging. Allow 5 to 7 hours  
without interruption for the Battery Pack to fully recharge. Or, replace the  
Handset’s Battery Pack with a charged Battery Pack.  
Cleaning the Battery Contacts  
CONTACTS  
CONTACTS  
To maintain a good charge, it is important to clean all charge contacts on the  
Handset and Base Unit about once a month. Use a pencil eraser or other  
contact cleaner. Do not use any liquids or solvents  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
Using Your EXP 9100  
NOTE: Refer to the foldout located in the back of this Operating Guide to  
help familiarize you with the features of your cordless phone.  
Preparing the Base Unit and Handset  
1. On the Base Unit, select either Pulse Dialing or Tone Dialing, depending  
on your local service.  
2. Set the Base Unit RINGER/VOLUME switch to either “LO” or “HI” enabling  
the Base Unit to ring when a call or page is received.  
3. Set the Handset RING/BATT SAVE switch so the Handset will ring when  
receiving a call.  
NOTE: The TALK LED and keypad lights flash when the Handset receives a  
call regardless of the RING/BATT SAVE switch position.  
4. Press the FLASH /R. TONE button on the Handset to select either of two  
ringer sounds. (Note: This sets the ringer tone only when the phone is  
not in use.)  
5. Press the VOL/R. VOL button on the Handset to select either high,  
medium, or low ringer volume. (Note: This sets the ringer volume only  
when the phone is not in use.)  
During a Call  
Handset Earpiece Volume:  
Press VOL R. VOL on the Handset to select a loud or soft volume level in  
/
the Handset earpiece.  
Mute Mode:  
Press MUTE to turn off the Handset’s microphone. The MUTE LED lights  
to show Mute Mode is active. Use this feature to consult another person  
in the room without the caller hearing you.  
Out of Range Indicator:  
When the Handset is reaching the end of the EXP 9100’s range limit, a  
beep sounds in the earphone every four seconds. If the Handset goes  
farther out of range, the warning beeps every 1.5 seconds. You must  
go back into range within 20 seconds or the call will be dropped.  
Keypad Lights:  
The Handset’s Keypad Lights flash when a call is received and remain lit  
for 10 seconds. Also, pressing any button on the Handset turns on the  
Keypad Lights for 10 seconds.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
Answering a Call  
1. The Handset rings and the green TALK LED and Keypad Lights flash.  
2. If the Handset is not in the Base Unit, press TALK to answer the call.  
3. If the Handset is in the Base Unit, the AutoTalk feature allows you to  
answer the call by simply picking up the Handset and beginning your  
conversation.  
4. When you finish the call, place the Handset back on the Base Unit.  
AutoStandby automatically hangs up the phone. There is no need to  
press TALK to hang up.  
—OR–  
If the Handset is away from the Base Unit, press TALK to hang up the  
phone.  
Making a Call  
1. Remove the Handset from the Base Unit  
2. Press TALK.  
NOTE: The TALK LED flashes and there is a slight delay while the Spread  
Spectrum Technology in your EXP 9100 sets up a digital link  
between the Handset and the Base Unit.  
3. When the TALK LED glows steadily and you hear a dial tone, dial the  
number you are calling by pressing the numbers on the keypad or using  
one of the memory features (See “Using Your EXP 9100 Memory.”)  
4. When you finish the call, place the Handset back on the Base Unit.  
AutoStandby automatically hangs up the phone. There is no need to  
press TALK to hang up.  
—OR–  
If the Handset is away from the Base Unit, press TALK to hang up the  
phone.  
Dialing a Stored Number  
1. Remove the Handset from the Base Unit  
2. Press TALK  
.
3. Press MEMO and the memory number (01-20) for that number.  
-OR-  
Press the ONE-TOUCH DIALING button for that number.  
4. Your EXP 9100 will then dial the previously stored number.  
(To store a number, refer to “Using Your EXP 9100 Memory.”)  
NOTE: If you select a memory location that does not have a stored number,  
the Handset will beep rapidly and the phone will not dial.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
Chain Dialing  
On certain occasions, after dialing a number, you may be requested by the  
party or service you are calling to enter a special access code, such as when  
performing a banking transaction.  
1. Remove the Handset from the Base Unit.  
2. Store the access code into one of the memory numbers. (See “Using  
Your EXP 9100 Memory.”)  
3. After dialing the main number, press MEMO and the memory number of  
the access code at the appropriate time.  
Example:  
a. Dial the number for your bank.  
- When the bank requests your account number:  
b. Press MEMO  
c. Press the memory location number for your account number.  
Your Handset dials the number and you may proceed with your  
transaction.  
Special Features  
Placing a Call On Hold  
1. Press HOLD on the Handset during the call, and the TALK LED flashes.  
NOTE: If you wish to page the Base Unit while the call is holding, refer to the  
section “Using your EXP 9100 Intercom.”  
2. To pick up the call holding, press TALK on the Handset.  
Monitoring a Call  
Press MONITOR on the Handset during a call. This feature amplifies the earpiece  
audio through the Monitor Speaker on the Handset so you can monitor a call  
without having the phone next to the ear. The Handset microphone is turned off  
during monitoring.  
Using the FLASH/R. TONE Button  
Press the FLASH/R. TONE button while operating the Handset. This feature  
sends a timed “hook-flash” on the telephone line for accessing services such  
as Call Waiting, etc.  
Last Number Redial  
Press RDL/P to dial the last number that you called. This feature is extremely  
useful when the number you called is busy.  
NOTE: If any other key is pressed before RDL/P, the phone will not redial  
the last number.  
Download from Www.Somanuals.co1m6. All Manuals Search And Download.  
Using Your EXP 9100 Memory  
Storing a Number  
1. Remove the Handset from the Base Unit  
2. Press MEMO (The TALK LED lights and you hear a beep.)  
3. Enter the number (up to 16 digits) you want to store.  
You may enter a delay between numbers (for accessing a switchboard,  
or long distance service) by pressing RDL/P at the point in the number  
sequence you wish to pause. (Note: The RDL/P button counts as one  
digit.) Pressing RDL/P more than once will increase the length of the  
pause between numbers.  
4. Press MEMO and a number (01-20) for the memory location.  
After pressing MEMO the second time, you have 20 seconds to  
enter the number you wish to store. Otherwise, an error tone will  
sound and the unit returns to stand-by.  
You will hear a confirmation beep and the TALK LED goes out.  
5. Write the stored number and its memory location number on one of the  
enclosed stickers.  
Example: Store 555-1234 in memory location 12:  
a. Press MEMO  
b. Press 5551234  
c. Press MEMO  
d. Press 12  
The Handset beeps confirmation and the TALK LED goes out.  
Storing a One-Touch Dialing Number:  
1. Follow steps 1 - 3 above in “Storing a Number,” then:  
2. Press MEMO and the ONE-TOUCH DIALING button (A, B, or C) you wish to  
program. The Handset beeps confirmation and the TALK LED goes out.  
Example: Store 555-1234 in One-Touch button B:  
a. Press MEMO  
b. Press 5551234  
c. Press MEMO  
d. Press  
B
Handset beeps confirmation and the TALK LED goes out.  
Download from Www.Somanuals.co1m7. All Manuals Search And Download.  
Storing Mixed Tone/Pulse numbers:  
If your Base Unit is set up for Pulse Dialing, you can store a mixed mode  
number (up to 16 digits) to easily access long distance services or other  
services requiring Tone inputs.  
1. Follow steps 1 and 2 in “Storing a Number,” then:  
2. Enter the number to be dialed in Pulse Mode.  
3. Press the TONE button on the Handset  
(NOTE: The TONE button counts as one digit.)  
4. Enter the number to be dialed in Tone Mode.If desired, press RDL/P to  
enter delays between numbers.  
5. Follow steps 4 and 5 in “Storing a Number.”  
Example: Store 555-1234, plus tone number 765-4321 in memory  
location 18:  
a. Press MEMO  
b. Press 5551234  
c. Press RDL/P (To enter delay between numbers)  
d. Press TONE (Switches Handset to Tone Mode; counts as one digit)  
e. Press 7654321 (Number entered in Tone Mode)  
f. Press MEMO  
g. Press 18  
Handset beeps confirmation and the TALK LED goes out.  
Erasing a Stored Number  
1. Remove the Handset from the Base Unit.  
2
Press MEMO twice.  
3. Press the memory location number or the ONE-TOUCH DIALING button you  
want to clear. You will hear a long beep confirming that you have  
erased the number.  
Using your EXP 9100 Intercom  
NOTE: The RING ON/BATT SAVE switch on the Handset must be in the  
RING ON” position.  
The Base Unit RINGER/VOLUME switch must be set to either  
LO” or “HI”.  
Paging from the Base Unit  
1. Press INT’COM. (If no answer, press INT’COM again to disconnect.)  
2. Press TALK or INT’COM on the Handset to answer the page.  
Speak into the mouthpiece.  
3. To turn off the Intercom, press INT’COM on the Base Unit  
— OR —  
Press TALK or INT’COM on the Handset.  
Download from Www.Somanuals.co1m8. All Manuals Search And Download.  
Paging the Base Unit While a Call is Holding  
1. Press INT’COM on the Handset. If no answer, press TALK or INT’COM to  
disconnect and return to the call ON HOLD.  
2. At the Base Unit, press INT’COM to answer the page. Speak into the  
microphone.  
3. To turn off the Intercom press INT’COM at the Base Unit  
— OR —  
Press TALK on the Handset. The Handset returns to the call ON HOLD.  
Paging from the Handset to the Base Unit  
1. Press INT’COM. on the Handset (If no answer, press INT’COM again to  
disconnect.)  
2. At the Base Unit, press INT’COM to answer the page. Speak into the  
microphone.  
3. To turn off the Intercom, press INT’COM at the Base Unit  
— OR —  
Press TALK or INT’COM on the Handset.  
Using the EXP 9100 as a Room Monitor  
You may use the EXP 9100 Handset to monitor activity near the Base Unit  
without anyone present at the Base Unit.  
To turn Room Monitoring on:  
1. Remove the Handset from the Base Unit.  
2. Press INT’COM on the Handset.  
3. Press TALK on the Handset. Two-way communications are now set up  
between the Base Unit and the Handset.  
NOTE: Press VOL/RVOL on the Handset to adjust the earpiece volume to  
loud or soft.  
4. To change to one-way communication (Handset to Base only) for private  
listening, press MONITOR on the Handset.  
NOTE: Press VOL/RVOL on the Handset to adjust the Monitor Speaker  
volume to loud or soft.  
To turn monitoring off, press TALK at the Handset.  
Download from Www.Somanuals.co1m9. All Manuals Search And Download.  
Troubleshooting  
If your EXP 9100 Cordless Telephone is not performing to your expectations,  
please try these simple steps. If you are still unable to resolve the problems,  
contact Uniden Customer Service at: (800) 297-1023, 8 AM to 5 PM Central,  
Monday through Friday. Note: Do not attempt to service this unit yourself.  
All service must be done by qualified service personnel.  
Problem  
Suggestion  
Charge light won’t come on when  
Handset is placed in Base Unit.  
Make sure the AC Adapter is plugged  
into the Base Unit and wall outlet.  
Make sure Handset is properly seated  
in Base Unit.  
Make sure the Nickel-Cadmium Battery  
Pack is properly placed inside the  
Handset.  
Make sure that the charging contacts  
on the Handset and Base Unit are clean.  
Make sure that the Base Unit antenna  
is fully vertical.  
Audio sounds weak and/or scratchy.  
Make sure that there are no obstacles  
(walls, doors, etc.) in line-of-sight  
between the Base Unit and the Handset.  
Move the Handset and/or Base Unit to  
different locations and try again.  
Check both ends of the Base Unit  
telephone line cord.  
Can’t make or receive calls.  
Make sure the AC Adapter is plugged  
into the Base Unit and wall outlet.  
Disconnect the AC Adapter for a few  
minutes, and then reconnect it.  
Nickel-Cadmium Battery Pack may be  
weak. Charge the battery on the Base  
Unit for more than 5 to 7 hours.  
Set the RING ON/BATT SAVE switch on  
the Handset to “RING ON”.  
Handset doesn’t ring or receive a page.  
Make sure the Base Unit antenna is  
fully vertical.  
Make sure that there are no obstacles  
(walls, doors, etc.) in line-of-sight  
between the Base Unit and the Handset.  
The Handset may be too far away from  
the Base Unit.  
Place the Base Unit away from noise  
sources.  
The Digital Security Code may be  
erased. Set the Digital Code.  
(See page 5 for instructions.)  
Base Unit doesn’t ring or receive a page.  
Set the Base Unit RINGER/VOLUME  
switch to “LO” or “HI”.  
Download from Www.Somanuals.co2m0. All Manuals Search And Download.  
Important Electrical Considerations  
Unplug all electrical appliances when you know an electrical storm is  
approaching. Lightning can pass through your household wiring and damage  
any device connected to it. The EXP 9100 is no exception.  
Note: Please do not attempt to unplug any appliance during an electrical  
storm.  
Range  
The EXP 9100 is designed to achieve the maximum possible range by  
transmitting and receiving according to the highest specifications set forth by  
the FCC. We have rated this phone to operate at a maximum distance with the  
qualification that the range depends upon the environment in which the  
telephone is used. Many factors limit range, and it would be impossible to  
include all the variables in our rating. The Maximum Range rating of the  
EXP 9100 is meant to be used as a means of comparison against other range  
claims.  
Telephone Line Problems  
The FCC has granted the telephone company the right to disconnect service in  
the event that your EXP 9100 causes problems on the telephone line. Also, the  
telephone company may make changes in facilities and services which may  
effect the operation of your unit. However, your telephone company must give  
adequate notice in writing prior to such actions to allow you time for making  
necessary arrangements to continue uninterrupted service.  
If you are having trouble with your telephone service, you must first disconnect  
the EXP 9100 to determine if it is the cause of your problem. If you determine  
that it is the cause, you must leave it disconnected until the trouble has been  
corrected.  
Radio Interference  
Radio interference may occasionally cause buzzing and humming in your  
cordless Handset, or clicking noises in the Base Unit. This interference is  
caused by external sources such as TV, refrigerator, vacuum cleaner,  
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these  
noises continue and are too distracting, please check around your home to see  
what appliances may be causing the problem. In addition, we recommend that  
the base not be plugged into a circuit that also powers a major appliance  
because of the potential for interference.  
More Than One Cordless Telephone  
Other cordless phones will not interfere with your EXP 9100. Spread Spectrum  
Technology and Auto Channel Scan allow your EXP 9100 to operate on a clear  
frequency at all times.  
Download from Www.Somanuals.co2m1. All Manuals Search And Download.  
Specifications  
GENERAL  
The EXP 9100 complies with FCC Part 15 and 68.  
: Crystal controlled transmission  
: MSK  
Frequency Control  
Modulation  
°
°
Operating Temperature  
: -10 to 50 C  
Base Unit  
Receive/Transmit Frequency : 903.087 to 925.615 MHz (23 Channels)  
Power Requirements  
Size  
: 120V AC, 60 Hz  
: 634 in. W X 87 in. D X 3352 in. H  
170mm W X 22mm D X 80mm H  
: Approx. 1 lb., 5 oz. (590g)  
Weight  
Handset  
Receive/Transmit Frequency : 903.087 to 925.615 MHz (23 Channels)  
Power Requirements  
Size  
: Rechargeable Ni-Cd Battery Pack  
3
: 2 38 in. W x 2 16 in. D x 9 58 in. H with antenna  
60mm W X 55mm D X 245mm H with antenna  
: Approx. 12 oz. (345g) with battery  
: BT-9100  
Weight  
Battery  
Capacity  
600 mAH, 6V  
3 hours (typical)  
1 week  
Talk Mode  
Standby Mode  
Specifications shown are typical and subject to change without notice.  
Download from Www.Somanuals.co2m2. All Manuals Search And Download.  
®
EXP 9100  
Cordless Telephone  
Operating Guide  
 
PRECAUTIONS  
Before you read anything else,  
please observe the following:  
WARNING!  
Uniden America Corporation DOES NOT represent this unit to be  
waterproof. To reduce the risk of fire, electrical shock, or damage  
to the unit, DO NOT expose this unit to rain or moisture.  
NICKEL-CADMIUM BATTERY WARNING  
This equipment contains a Nickel-Cadmium  
Battery.  
Cadmium is a chemical known to the State of  
California to cause cancer.  
The Nickel-Cadmium Battery contained in this  
equipment may explode if disposed of in a fire.  
Do not short circuit the battery.  
Do not charge the Nickel-Cadmium Battery  
used in this equipment in any other charger  
other than the one designed to charge this  
battery. Using another charger may damage  
the battery, or cause the battery to explode.  
Nickel-Cadmium Battery Disposal  
Nickel-Cadmium Batteries must be disposed of properly.  
Read the Nickel-Cadmium Battery Disposal package  
insert for important information.  
®
Uniden is a registered trademark of Uniden America Corporation.  
AutoStandbyTM and AutoTalkTM are trademarks of Uniden America  
Corporation. AutoStandby is a patented invention of Uniden America  
Corporation.  
 
One Year Limited Warranty  
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)  
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail  
owner, this Uniden Product to be free from defects in materials and craftsmanship with  
only the limitations or exclusions set out below.  
WARRANTY DURATION: This warranty to the original user shall terminate and be of  
no further effect 12 months after the date of original retail sale. The warranty is invalid if  
the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified,  
altered, or used as part of any conversion kits, subassemblies, or any configurations not  
sold by Uniden, (C) improperly installed, (D) repaired by someone other than an  
authorized service center for a defect or malfunction covered by this warranty, (E) used  
in any conjunction with equipment or parts or as part of any system not manufactured by  
Uniden, or (F) installed, programmed, or serviced by anyone other than an authorized  
Uniden service center.  
STATEMENT OF REMEDY: In the event that the product does not conform to this  
warranty at any time while this warranty is in effect, warrantor will repair the defect and  
return it to you without charge for parts, service, or any other cost (except shipping and  
handling) incurred by warrantor or its representatives in connection with the performance  
of this warranty. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND  
ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND  
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER,  
WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,  
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR  
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER  
OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of  
incidental or consequential damages so the above limitation or exclusion may not apply  
to you.  
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state. This warranty is void outside the United  
States of America.  
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following  
the instructions in this Operating Guide you are certain that the Product is defective,  
pack the Product carefully (preferably in its original packaging). Include evidence of  
original purchase and a note describing the defect that has caused you to return it. The  
Product should be shipped or delivered (by UPS or insured parcel post), freight prepaid  
to warrantor at:  
Uniden America Corporation  
Parts and Service Division  
4700 Amon Carter Blvd.  
Ft. Worth TX 76155  
(800) 297-1023, 8 AM to 5 PM Central, Monday through Friday  
 
®
© 1993 Uniden America Corporation. All rights reserved.  
ZUDUD01304AZ  
Printed in Hong Kong  
 
Base Unit Controls & Functions  
Tone/Pulse  
Switch  
Line Out  
Fold Down  
Legs  
Ringer/Volume  
Switch  
Line In  
AC Adapter  
Connection  
Base Unit Antenna  
Speaker  
Handset  
Retainer  
Battery  
Compartment  
Intercom LED  
Power LED  
Charge LED  
Battery Charge LED  
Handset  
Support  
Charging  
Contacts  
Microphone  
Intercom Button  
 
Handset Controls & Functions  
Handset  
Antenna  
Ring On  
Battery Save  
Switch  
Earpiece  
RING  
ON  
Hold Button  
BATT  
SAVE  
Talk Button  
Mute Button  
Monitor Button  
1 – 9, 0,  
,
# Buttons  
Tone Button  
Intercom Button  
One-Touch Buttons  
Memory Button  
Flash and Ringer Tone  
Button  
Volume and  
Ringer Volume  
Button  
Redial/Pause Button  
Monitor Speaker  
Microphone  
 

Texas Instruments Stereo Amplifier THS4150 User Manual
The Vollrath Co Cookware T 43R User Manual
Toastmaster Griddle TMEG15W B User Manual
Toshiba Computer Drive MK5056GSY User Manual
Vent a Hood Ventilation Hood XR9 XRH9 User Manual
ViewSonic Car Video System N1700w User Manual
Vizio Car Satellite TV System E4011 A2 User Manual
Vizio Universal Remote XRU9M User Manual
Waring Juicer PCJ201 User Manual
Weber Gas Grill 55279 User Manual