Tripp Lite Speaker SRX2 User Manual

SRX2, SRX3 and SRX4  
Rack Mount Fixed And Roll-Out Shelves  
CLIP NUT INSTALLATION  
Clip Nuts provide mounting points for rack mount  
fixed and roll-out shelves.  
Clip nuts have a front or screw side. Consider which  
way it should face for ease of access to the screw  
head during component installation. (figure 1)  
Rack Mount Fixed And Roll-Out Shelves  
Clip nut  
To remove a clip nut from a mounting angle, insert a flat  
blade screwdriver or knife under the tab on the front and  
pry up, freeing the retaining ring from the mounting  
angle. (figure 2)  
#10-32 x 5/8" Pan  
Head Machine Screw  
Front or screw side  
1. Select the location at which the shelf will be mounted  
in the enclosure assembly.  
Figure 1  
2. Snap one clip nut into the top hole of the selected  
location.  
Mounting angle  
(note: When mounting a roll-out shelf, insert a  
10-32 screw partially into each clip nut.)  
If the weight load will exceed 75 lbs. on a roll-out shelf,  
use four clip nuts and screws in each of the brackets.  
It will be necessary to select a four-hole grouping that  
matches the mounting holes in the brackets. The center  
two holes will measure 1/2" apart.  
Clip nut  
Two screws per bracket, one at the front and one at the  
rear, is sufficient if the weight load will be less than  
75 lbs.  
3. Measure from the bottom of the Mounting Angle to the  
top clip nut. Assemble clip nuts onto the three other rails  
at the measured height.  
Figure 2  
Manual Part #93-1937  
01/18/02 rev. A  
1
 
Stationary Shelf Bracket  
Cable Management Arm  
(included with SRX4 only)  
SRX2, SRX3 and SRX4  
Rack Mount Fixed And Roll-Out Shelves  
Required Tools:  
#8-32 Hex Lock Nut  
Phillips Head Screwdriver  
3/8” Nut Driver (or Socket Wrench)  
11/32” Nut Driver (or Socket Wrench)  
#8-32 x 3/8" Phillips Pan  
Head Machine Screw  
Fasteners That May Be Required:  
#10-32 x 3/8” Phillips  
Pan Head Screw  
#10-32 x 5/8” Phillips  
Machine Screw  
#10-32 Clip Nut  
#10-32 Keps Locking Nut  
SRX4 Parts List  
SRX2 & SRX3 Parts List  
Item  
Description  
Qty.  
Item  
Description  
Qty.  
#10-32 x 5/8 Screw  
#10-32 Clip Nut  
Slide Bracket  
16  
16  
2
1
2
3
4
5
#10-32 x 5/8" Screw  
#10-32 x 3/8" Screw  
#10-32 Keps Locking Nut  
#10-32 Clip Nut  
12  
8
1
2
3
4
5
8
Warning Label  
1
12  
4
2
#8-32 x 3/8 Screw  
Stationary Shelf Bracket  
2
1
6
7
#8-32 Keps Locking Nut  
Cable Management Arm  
Manual Part #93-1937  
01/18/02 rev. A  
3
 

TDK Power Supply ZMG 11 User Manual
Toshiba Personal Computer PROA660 User Manual
Trane Fan RT PRC005 User Manual
Tricity Bendix Cooktop SIE524 User Manual
Tricity Bendix Oven SI 055 User Manual
Troy Bilt Blower TB197BV User Manual
Uniden Cordless Telephone 388 2 User Manual
Vent a Hood Ventilation Hood SLH6 K User Manual
VXI Microwave Oven Microwave Matrix User Manual
Weed Eater Blower 530163993 User Manual